THE EFFECT OF ELECTROLYTE-PLASMA HARDENING PARAMETERS ON THE MICROSTRUCTURE, PHASE COMPOSITION, AND MECHANICAL AND TRIBOLOGICAL PROPERTIES OF 20X STEEL
https://doi.org/10.53360/2788-7995-2026-3(23)-33
Abstract
This article investigates the effect of electrolytic-plasma treatment (EPT) parameters–voltage (260-320 V) and dwell time (2-5 s) – on the microstructure, phase composition, microhardness, elastic modulus, and tribological properties of 20X steel. Treatment was performed in a 12 wt.% Na₂CO₃ aqueous solution. X-ray diffraction and scanning electron microscopy showed the formation of α′-martensite with a bodycentered cubic (BCC) lattice without residual austenite or carbide phases. The threshold treatment mode was 260 V for 2 s, at which complete austenitization was not achieved. Increasing the dwell time to 5 s at 300 V nearly doubled the microhardness to 441.66 HV, while increasing voltage at 2 s primarily affected carbon supersaturation. The lowest friction coefficient (μ = 0.498) was obtained at 320 V for 2 s, indicating that maximum hardness does not necessarily correspond to the best tribological performance. The results demonstrate that EPT parameters should be selected according to the required operational properties of 20X steel.
Keywords
About the Authors
А. E. KusainovKazakhstan
Arystanbek Kussainov – PhD doctoral student in Technical Physics
070004, Kazakhstan , Ust-Kamenogorsk, Serikbayev str. 19
G. Zh. Zhunissova
Kazakhstan
Gulnara Zhuniskyzy Zhunissovа – Master of Technical Physics
070004, Kazakhstan , Ust-Kamenogorsk, Serikbayev str. 19
N. M. Magazov
Kazakhstan
Nurtoleu Magazov – Researcher, Scientific Center «Protective and Functional Coatings»
070004, Kazakhstan , Ust-Kamenogorsk, Serikbayev str. 19
A. B. Kengesbekov
Kazakhstan
Aidar Kengesbekov – PhD, Leading Researcher at the Scientific Center «Protective and Functional Coatings»
070004, Kazakhstan , Ust-Kamenogorsk, Serikbayev str. 19
L. B. Bayatanova
Kazakhstan
Lyaila Bolatkanovna Bayatanova – PhD, Associate Professor
070004, Kazakhstan , Ust-Kamenogorsk, Serikbayev str. 19
References
1. Spectroscopic study of electrolytic-plasma discharge during hardening of 20GL steel and its effect on microstructure and mechanical properties / B. Rakhadilov et al // Crystals. – 2025. – Vol. 15, № 11. – Art. 976. https://doi.org/10.3390/cryst15110976.
2. Adhesion mechanisms, evaluation techniques and modeling strategies in PVD coatings: from fundamentals to data-driven design / S.G. Jan et al // Journal of Materials Research and Technology. – 2026. – Available online. https://doi.org/10.1016/j.jmrt.2026.01.234.
3. Influence of plasma electrolytic hardening modes on the structure and properties of 65G steel / B.K. Rakhadilov et al // Eurasian Journal of Physics and Functional Materials. – 2021. – Vol. 5, № 3. – P. 209-221. https://doi.org/10.32523/ejpfm.2021050306.
4. Investigation of changes in the structural-phase state and the efficiency of hardening of 30CrMnSiA steel by the method of electrolytic plasma thermocyclic surface treatment / D. Baizhan et al // Coatings. – 2022. – Vol. 12, № 11. – Art. 1696. https://doi.org/10.3390/coatings12111696.
5. Investigation of the effect of technological parameters of the electrolyte-plasma carburization method on the phase structure and mechanical properties of 20X structural steel / B. Rakhadilov et al // AIMS Materials Science. – 2023. – Vol. 10, № 5. – P. 934-947.
6. Experimental and mathematical modeling study of plasma electrolytic oxidation (PEO) for surface hardening of 20Ch steel / K. Kombayev et al // Materials. – 2024. – Vol. 17, № 24. – Art. 6043. https://doi.org/10.3390/ma17246043.
7. Effect of electrolytic-plasma hardening on the microstructure and tribological properties of lowalloy steels / B. Rakhadilov et al // Metals. – 2025. – Vol. 15, № 7. – Art. 698. https://doi.org/10.3390/met15070698.
8. The impact of technological parameters of electrolytic-plasma treatment on changes in the mechano-tribological properties of steel 45 / B. Rakhadilov et al // AIMS Materials Science. – 2024. – Vol. 11, № 4. – P. 666-683.
9. GOST 4543-2016. Metal products made of structural alloy steel. Specifications. – Moscow: Standartinform, 2017. – 31 p. (In Russian).
10. Effect of electropolishing on the microstructure and tribological properties of electrolyte-plasma borided layers on 30KhGSA steel / L. Sulyubayeva et al // Materials. – 2025. – Vol. 18, № 21. – Art. 4867. https://doi.org/10.3390/ma18214867.
11. ASTM G99-17. Standard test method for wear testing with a pin-on-disk apparatus. – West Conshohocken, PA: ASTM International, 2017.
12. ASTM G133-05(2016). Standard test method for linearly reciprocating ball-on-flat sliding wear. – West Conshohocken, PA: ASTM International, 2016.
13. ISO 14577-1:2015. Metallic materials – Instrumented indentation test for hardness and materials parameters – Part 1: Test method. – Geneva : International Organization for Standardization, 2015.
Review
For citations:
Kusainov А.E., Zhunissova G.Zh., Magazov N.M., Kengesbekov A.B., Bayatanova L.B. THE EFFECT OF ELECTROLYTE-PLASMA HARDENING PARAMETERS ON THE MICROSTRUCTURE, PHASE COMPOSITION, AND MECHANICAL AND TRIBOLOGICAL PROPERTIES OF 20X STEEL. Bulletin of Shakarim University. Technical Sciences. 2026;(3(23)):351-361. https://doi.org/10.53360/2788-7995-2026-3(23)-33
JATS XML















