<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE article PUBLIC "-//NLM//DTD JATS (Z39.96) Journal Publishing DTD v1.3 20210610//EN" "JATS-journalpublishing1-3.dtd">
<article article-type="research-article" dtd-version="1.3" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xml:lang="ru"><front><journal-meta><journal-id journal-id-type="publisher-id">kaz44</journal-id><journal-title-group><journal-title xml:lang="ru">Вестник Университета Шакарима. Серия технические науки</journal-title><trans-title-group xml:lang="en"><trans-title>Bulletin of Shakarim University. Technical Sciences</trans-title></trans-title-group></journal-title-group><issn pub-type="ppub">2788-7995</issn><issn pub-type="epub">3006-0524</issn><publisher><publisher-name>«Шәкәрім университеті» КеАҚ</publisher-name></publisher></journal-meta><article-meta><article-id pub-id-type="doi">10.53360/2788-7995-2026-3(23)-33</article-id><article-id custom-type="elpub" pub-id-type="custom">kaz44-2953</article-id><article-categories><subj-group subj-group-type="heading"><subject>Research Article</subject></subj-group><subj-group subj-group-type="section-heading" xml:lang="ru"><subject>МАШИНОСТРОЕНИЕ И МЕХАНИКА (ОРИГИНАЛЬНАЯ СТАТЬЯ)</subject></subj-group><subj-group subj-group-type="section-heading" xml:lang="en"><subject>MECHANICAL ENGINEERING AND MECHANICS (ORIGINAL ARTICLE)</subject></subj-group></article-categories><title-group><article-title>ВЛИЯНИЕ ПАРАМЕТРОВ ЭЛЕКТРОЛИТНО-ПЛАЗМЕННОГО УПРОЧНЕНИЯ НА МИКРОСТРУКТУРУ, ФАЗОВЫЙ СОСТАВ И МЕХАНИЧЕСКИЕ И ТРИБОЛОГИЧЕСКИЕ СВОЙСТВА СТАЛИ 20Х</article-title><trans-title-group xml:lang="en"><trans-title>THE EFFECT OF ELECTROLYTE-PLASMA HARDENING PARAMETERS ON THE MICROSTRUCTURE, PHASE COMPOSITION, AND MECHANICAL AND TRIBOLOGICAL PROPERTIES OF 20X STEEL</trans-title></trans-title-group></title-group><contrib-group><contrib contrib-type="author" corresp="yes"><contrib-id contrib-id-type="orcid">https://orcid.org/0000-0003-4623-4681</contrib-id><name-alternatives><name name-style="eastern" xml:lang="ru"><surname>Кусайнов</surname><given-names>А. Е.</given-names></name><name name-style="western" xml:lang="en"><surname>Kusainov</surname><given-names>А. E.</given-names></name></name-alternatives><bio xml:lang="ru"><p>Арыстанбек Ерланович Кусайнов – докторант по специальности «Техническая физика»</p><p>070004, Казахстан , г. Усть-Каменогорск, ул. Серикбаева, 19</p></bio><bio xml:lang="en"><p>Arystanbek Kussainov – PhD doctoral student in Technical Physics</p><p>070004, Kazakhstan , Ust-Kamenogorsk, Serikbayev str. 19</p><p> </p></bio><email xlink:type="simple">arys20055@gmail.com</email><xref ref-type="aff" rid="aff-1"/></contrib><contrib contrib-type="author" corresp="yes"><contrib-id contrib-id-type="orcid">https://orcid.org/0009-0008-2277-6666</contrib-id><name-alternatives><name name-style="eastern" xml:lang="ru"><surname>Жүнісова</surname><given-names>Г. Ж.</given-names></name><name name-style="western" xml:lang="en"><surname>Zhunissova</surname><given-names>G. Zh.</given-names></name></name-alternatives><bio xml:lang="ru"><p>Гүлнара Жүнісқызы Жүнісова – магистр по специальности «Техническая физика»</p><p>070004, Казахстан , г. Усть-Каменогорск, ул. Серикбаева, 19</p></bio><bio xml:lang="en"><p>Gulnara Zhuniskyzy Zhunissovа – Master of Technical Physics</p><p>070004, Kazakhstan , Ust-Kamenogorsk, Serikbayev str. 19</p></bio><email xlink:type="simple">junusova6@gmail.com</email><xref ref-type="aff" rid="aff-2"/></contrib><contrib contrib-type="author" corresp="yes"><contrib-id contrib-id-type="orcid">https://orcid.org/0000-0002-9941-9199</contrib-id><name-alternatives><name name-style="eastern" xml:lang="ru"><surname>Магазов</surname><given-names>Н. М.</given-names></name><name name-style="western" xml:lang="en"><surname>Magazov</surname><given-names>N. M.</given-names></name></name-alternatives><bio xml:lang="ru"><p>Нуртолеу Магзумбекович Магазов – научный сотрудник, Научный центр «Защитные и функциональные покрытия»</p><p>070004, Казахстан , г. Усть-Каменогорск, ул. Серикбаева, 19</p></bio><bio xml:lang="en"><p>Nurtoleu Magazov – Researcher, Scientific Center «Protective and Functional Coatings»</p><p>070004, Kazakhstan , Ust-Kamenogorsk, Serikbayev str. 19</p></bio><email xlink:type="simple">magazovn@gmail.com</email><xref ref-type="aff" rid="aff-1"/></contrib><contrib contrib-type="author" corresp="yes"><contrib-id contrib-id-type="orcid">https://orcid.org/0000-0002-5630-9467</contrib-id><name-alternatives><name name-style="eastern" xml:lang="ru"><surname>Кеңесбеков</surname><given-names>А. Б.</given-names></name><name name-style="western" xml:lang="en"><surname>Kengesbekov</surname><given-names>A. B.</given-names></name></name-alternatives><bio xml:lang="ru"><p>Айдар Бақытбекұлы Кеңесбеков – PhD, ведущий научный сотрудник научного центра «Защитные и функциональные покрытия»</p><p>070004, Казахстан , г. Усть-Каменогорск, ул. Серикбаева, 19</p></bio><bio xml:lang="en"><p>Aidar Kengesbekov – PhD, Leading Researcher at the Scientific Center «Protective and Functional Coatings» </p><p>070004, Kazakhstan , Ust-Kamenogorsk, Serikbayev str. 19</p></bio><email xlink:type="simple">kenesbekovaidar@gmail.com</email><xref ref-type="aff" rid="aff-1"/></contrib><contrib contrib-type="author" corresp="yes"><contrib-id contrib-id-type="orcid">https://orcid.org/0000-0002-5630-4746</contrib-id><name-alternatives><name name-style="eastern" xml:lang="ru"><surname>Баятанова</surname><given-names>Л. Б.</given-names></name><name name-style="western" xml:lang="en"><surname>Bayatanova</surname><given-names>L. B.</given-names></name></name-alternatives><bio xml:lang="ru"><p>Ляйла Болаткановна Баятанова – PhD, ассоциированный профессор («Центр физики»)</p><p>070004, Казахстан , г. Усть-Каменогорск, ул. Серикбаева, 19</p></bio><bio xml:lang="en"><p>Lyaila Bolatkanovna Bayatanova – PhD, Associate Professor</p><p>070004, Kazakhstan , Ust-Kamenogorsk, Serikbayev str. 19</p></bio><email xlink:type="simple">leila_1809@mail.ru</email><xref ref-type="aff" rid="aff-1"/></contrib></contrib-group><aff-alternatives id="aff-1"><aff xml:lang="ru"><institution>Восточно-Казахстанский технический университет им. Д. Серикбаева</institution><country>Казахстан</country></aff><aff xml:lang="en"><institution>D. Serikbayev East Kazakhstan Technical University</institution><country>Kazakhstan</country></aff></aff-alternatives><aff-alternatives id="aff-2"><aff xml:lang="ru"><institution>Восточно-Казахстанский технический университет им. Д. Серикбаева </institution><country>Казахстан</country></aff><aff xml:lang="en"><institution>D. Serikbayev East Kazakhstan Technical University</institution><country>Kazakhstan</country></aff></aff-alternatives><pub-date pub-type="collection"><year>2026</year></pub-date><pub-date pub-type="epub"><day>20</day><month>11</month><year>2026</year></pub-date><volume>0</volume><issue>3(23)</issue><fpage>351</fpage><lpage>361</lpage><permissions><copyright-statement>Copyright &amp;#x00A9; Кусайнов А.Е., Жүнісова Г.Ж., Магазов Н.М., Кеңесбеков А.Б., Баятанова Л.Б., 2026</copyright-statement><copyright-year>2026</copyright-year><copyright-holder xml:lang="ru">Кусайнов А.Е., Жүнісова Г.Ж., Магазов Н.М., Кеңесбеков А.Б., Баятанова Л.Б.</copyright-holder><copyright-holder xml:lang="en">Kusainov А.E., Zhunissova G.Z., Magazov N.M., Kengesbekov A.B., Bayatanova L.B.</copyright-holder><license xml:lang="ru" license-type="creative-commons-attribution" xlink:href="https://creativecommons.org/licenses/by/4.0/" xlink:type="simple"><license-p>Данная работа распространяется под лицензией Creative Commons Attribution 4.0.</license-p></license><license xml:lang="en" license-type="creative-commons-attribution" xlink:href="https://creativecommons.org/licenses/by/4.0/" xlink:type="simple"><license-p>This work is licensed under a Creative Commons Attribution 4.0 License.</license-p></license></permissions><self-uri xlink:href="https://tech.vestnik.shakarim.kz/jour/article/view/2953">https://tech.vestnik.shakarim.kz/jour/article/view/2953</self-uri><abstract><p>Данная статья исследует влияние параметров электролитно-плазменной обработки (ЭПО) напряжения (260-320 В) и времени выдержки (2-5 с) – на микроструктуру, фазовый состав, микротвёрдость, модуль упругости и трибологические свойства стали 20Х. Обработка проводилась в водном растворе Na₂CO₃ концентрацией 12 масс.%. Рентгеноструктурный анализ и растровая электронная микроскопия показали формирование α′-мартенсита с объёмноцентрированной кубической (ОЦК) решёткой без остаточного аустенита или карбидных фаз. Пороговым режимом обработки являлся режим 260 В при 2 с, при котором полная аустенитизация не достигалась. Увеличение времени выдержки до 5 с при 300 В почти удвоило микротвёрдость до 441,66 HV, тогда как повышение напряжения при 2 с преимущественно влияло на пересыщение твёрдого раствора углеродом. Минимальный коэффициент трения (μ = 0,498) был получен при 320 В в течение 2 с, что указывает на то, что максимальная твёрдость не всегда соответствует наилучшим трибологическим характеристикам. Полученные результаты демонстрируют, что параметры ЭПО должны подбираться в зависимости от требуемых эксплуатационных свойств стали 20Х.</p></abstract><trans-abstract xml:lang="en"><p>This article investigates the effect of electrolytic-plasma treatment (EPT) parameters–voltage (260-320 V) and dwell time (2-5 s) – on the microstructure, phase composition, microhardness, elastic modulus, and tribological properties of 20X steel. Treatment was performed in a 12 wt.% Na₂CO₃ aqueous solution. X-ray diffraction and scanning electron microscopy showed the formation of α′-martensite with a bodycentered cubic (BCC) lattice without residual austenite or carbide phases. The threshold treatment mode was 260 V for 2 s, at which complete austenitization was not achieved. Increasing the dwell time to 5 s at 300 V nearly doubled the microhardness to 441.66 HV, while increasing voltage at 2 s primarily affected carbon supersaturation. The lowest friction coefficient (μ = 0.498) was obtained at 320 V for 2 s, indicating that maximum hardness does not necessarily correspond to the best tribological performance. The results demonstrate that EPT parameters should be selected according to the required operational properties of 20X steel.</p></trans-abstract><kwd-group xml:lang="ru"><kwd>электролитно-плазменная обработка</kwd><kwd>сталь 20Х</kwd><kwd>мартенсит</kwd><kwd>микротвёрдость</kwd><kwd>фазовый состав</kwd><kwd>рентгенофазовый анализ</kwd><kwd>коэффициент трения</kwd><kwd>поверхностное упрочнение</kwd></kwd-group><kwd-group xml:lang="en"><kwd>electrolytic plasma treatment</kwd><kwd>20X steel</kwd><kwd>martensite</kwd><kwd>microhardness</kwd><kwd>phase composition</kwd><kwd>X-ray diffraction analysis</kwd><kwd>coefficient of friction</kwd><kwd>surface hardening</kwd></kwd-group><funding-group><funding-statement xml:lang="en">This article was prepared as part of the MNVO research grant project BR24992864 «Development of Equipment and Technologies for the Surface Treatment of Parts for the Metalworking Industry».</funding-statement></funding-group></article-meta></front><back><ref-list><title>References</title><ref id="cit1"><label>1</label><citation-alternatives><mixed-citation xml:lang="ru">Spectroscopic study of electrolytic-plasma discharge during hardening of 20GL steel and its effect on microstructure and mechanical properties / B. Rakhadilov et al // Crystals. – 2025. – Vol. 15, № 11. – Art. 976. https://doi.org/10.3390/cryst15110976.</mixed-citation><mixed-citation xml:lang="en">Spectroscopic study of electrolytic-plasma discharge during hardening of 20GL steel and its effect on microstructure and mechanical properties / B. Rakhadilov et al // Crystals. – 2025. – Vol. 15, № 11. – Art. 976. https://doi.org/10.3390/cryst15110976.</mixed-citation></citation-alternatives></ref><ref id="cit2"><label>2</label><citation-alternatives><mixed-citation xml:lang="ru">Adhesion mechanisms, evaluation techniques and modeling strategies in PVD coatings: from fundamentals to data-driven design / S.G. Jan et al // Journal of Materials Research and Technology. – 2026. – Available online. https://doi.org/10.1016/j.jmrt.2026.01.234.</mixed-citation><mixed-citation xml:lang="en">Adhesion mechanisms, evaluation techniques and modeling strategies in PVD coatings: from fundamentals to data-driven design / S.G. Jan et al // Journal of Materials Research and Technology. – 2026. – Available online. https://doi.org/10.1016/j.jmrt.2026.01.234.</mixed-citation></citation-alternatives></ref><ref id="cit3"><label>3</label><citation-alternatives><mixed-citation xml:lang="ru">Influence of plasma electrolytic hardening modes on the structure and properties of 65G steel / B.K. Rakhadilov et al // Eurasian Journal of Physics and Functional Materials. – 2021. – Vol. 5, № 3. – P. 209-221. https://doi.org/10.32523/ejpfm.2021050306.</mixed-citation><mixed-citation xml:lang="en">Influence of plasma electrolytic hardening modes on the structure and properties of 65G steel / B.K. Rakhadilov et al // Eurasian Journal of Physics and Functional Materials. – 2021. – Vol. 5, № 3. – P. 209-221. https://doi.org/10.32523/ejpfm.2021050306.</mixed-citation></citation-alternatives></ref><ref id="cit4"><label>4</label><citation-alternatives><mixed-citation xml:lang="ru">Investigation of changes in the structural-phase state and the efficiency of hardening of 30CrMnSiA steel by the method of electrolytic plasma thermocyclic surface treatment / D. Baizhan et al // Coatings. – 2022. – Vol. 12, № 11. – Art. 1696. https://doi.org/10.3390/coatings12111696.</mixed-citation><mixed-citation xml:lang="en">Investigation of changes in the structural-phase state and the efficiency of hardening of 30CrMnSiA steel by the method of electrolytic plasma thermocyclic surface treatment / D. Baizhan et al // Coatings. – 2022. – Vol. 12, № 11. – Art. 1696. https://doi.org/10.3390/coatings12111696.</mixed-citation></citation-alternatives></ref><ref id="cit5"><label>5</label><citation-alternatives><mixed-citation xml:lang="ru">Investigation of the effect of technological parameters of the electrolyte-plasma carburization method on the phase structure and mechanical properties of 20X structural steel / B. Rakhadilov et al // AIMS Materials Science. – 2023. – Vol. 10, № 5. – P. 934-947.</mixed-citation><mixed-citation xml:lang="en">Investigation of the effect of technological parameters of the electrolyte-plasma carburization method on the phase structure and mechanical properties of 20X structural steel / B. Rakhadilov et al // AIMS Materials Science. – 2023. – Vol. 10, № 5. – P. 934-947.</mixed-citation></citation-alternatives></ref><ref id="cit6"><label>6</label><citation-alternatives><mixed-citation xml:lang="ru">Experimental and mathematical modeling study of plasma electrolytic oxidation (PEO) for surface hardening of 20Ch steel / K. Kombayev et al // Materials. – 2024. – Vol. 17, № 24. – Art. 6043. https://doi.org/10.3390/ma17246043.</mixed-citation><mixed-citation xml:lang="en">Experimental and mathematical modeling study of plasma electrolytic oxidation (PEO) for surface hardening of 20Ch steel / K. Kombayev et al // Materials. – 2024. – Vol. 17, № 24. – Art. 6043. https://doi.org/10.3390/ma17246043.</mixed-citation></citation-alternatives></ref><ref id="cit7"><label>7</label><citation-alternatives><mixed-citation xml:lang="ru">Effect of electrolytic-plasma hardening on the microstructure and tribological properties of lowalloy steels / B. Rakhadilov et al // Metals. – 2025. – Vol. 15, № 7. – Art. 698. https://doi.org/10.3390/met15070698.</mixed-citation><mixed-citation xml:lang="en">Effect of electrolytic-plasma hardening on the microstructure and tribological properties of lowalloy steels / B. Rakhadilov et al // Metals. – 2025. – Vol. 15, № 7. – Art. 698. https://doi.org/10.3390/met15070698.</mixed-citation></citation-alternatives></ref><ref id="cit8"><label>8</label><citation-alternatives><mixed-citation xml:lang="ru">The impact of technological parameters of electrolytic-plasma treatment on changes in the mechano-tribological properties of steel 45 / B. Rakhadilov et al // AIMS Materials Science. – 2024. – Vol. 11, № 4. – P. 666-683.</mixed-citation><mixed-citation xml:lang="en">The impact of technological parameters of electrolytic-plasma treatment on changes in the mechano-tribological properties of steel 45 / B. Rakhadilov et al // AIMS Materials Science. – 2024. – Vol. 11, № 4. – P. 666-683.</mixed-citation></citation-alternatives></ref><ref id="cit9"><label>9</label><citation-alternatives><mixed-citation xml:lang="ru">GOST 4543-2016. Metal products made of structural alloy steel. Specifications. – Moscow: Standartinform, 2017. – 31 p. (In Russian).</mixed-citation><mixed-citation xml:lang="en">GOST 4543-2016. Metal products made of structural alloy steel. Specifications. – Moscow: Standartinform, 2017. – 31 p. (In Russian).</mixed-citation></citation-alternatives></ref><ref id="cit10"><label>10</label><citation-alternatives><mixed-citation xml:lang="ru">Effect of electropolishing on the microstructure and tribological properties of electrolyte-plasma borided layers on 30KhGSA steel / L. Sulyubayeva et al // Materials. – 2025. – Vol. 18, № 21. – Art. 4867. https://doi.org/10.3390/ma18214867.</mixed-citation><mixed-citation xml:lang="en">Effect of electropolishing on the microstructure and tribological properties of electrolyte-plasma borided layers on 30KhGSA steel / L. Sulyubayeva et al // Materials. – 2025. – Vol. 18, № 21. – Art. 4867. https://doi.org/10.3390/ma18214867.</mixed-citation></citation-alternatives></ref><ref id="cit11"><label>11</label><citation-alternatives><mixed-citation xml:lang="ru">ASTM G99-17. Standard test method for wear testing with a pin-on-disk apparatus. – West Conshohocken, PA: ASTM International, 2017.</mixed-citation><mixed-citation xml:lang="en">ASTM G99-17. Standard test method for wear testing with a pin-on-disk apparatus. – West Conshohocken, PA: ASTM International, 2017.</mixed-citation></citation-alternatives></ref><ref id="cit12"><label>12</label><citation-alternatives><mixed-citation xml:lang="ru">ASTM G133-05(2016). Standard test method for linearly reciprocating ball-on-flat sliding wear. – West Conshohocken, PA: ASTM International, 2016.</mixed-citation><mixed-citation xml:lang="en">ASTM G133-05(2016). Standard test method for linearly reciprocating ball-on-flat sliding wear. – West Conshohocken, PA: ASTM International, 2016.</mixed-citation></citation-alternatives></ref><ref id="cit13"><label>13</label><citation-alternatives><mixed-citation xml:lang="ru">ISO 14577-1:2015. Metallic materials – Instrumented indentation test for hardness and materials parameters – Part 1: Test method. – Geneva : International Organization for Standardization, 2015.</mixed-citation><mixed-citation xml:lang="en">ISO 14577-1:2015. Metallic materials – Instrumented indentation test for hardness and materials parameters – Part 1: Test method. – Geneva : International Organization for Standardization, 2015.</mixed-citation></citation-alternatives></ref></ref-list><fn-group><fn fn-type="conflict"><p>The authors declare that there are no conflicts of interest present.</p></fn></fn-group></back></article>
