EFFECT OF PLASMA HARDENING PARAMETERS ON 65G STEEL STRUCTURE AND PROPERTIES
https://doi.org/10.53360/2788-7995-2026-3(23)-74
Abstract
This article presents a study of the effect of plasma hardening parameters on the structure and properties of grade 65G steel. The effectiveness of plasma treatment in obtaining a hardened surface layer through localized high-speed heating followed by self-cooling of the material was demonstrated. The studies were conducted at plasma arc currents ranging from 130 to 150 A and plasma-forming gas flow rates of 0.22-0.25 L/min, which made it possible to evaluate the influence of the technological parameters on the characteristics of the resulting layer. The structural and phase composition were analyzed using X-ray diffraction and scanning electron microscopy, while the mechanical and tribological properties of the steel were evaluated using a hardness tester and a tribometer. A comparative study of the properties of 65G steel in the initial state and after plasma surface hardening was carried out. The obtained results indicate that plasma quenching promotes the formation of a gradient microstructure consisting of martensite and retained austenite, with a gradual transition to the initial structure of the material. The maximum microhardness of the hardened layer reaches 670-700 HV0.1. At the same time, the wear rate of the treated layer decreases by 5-6 times compared to the initial state. The results of the study confirm the potential of plasma quenching as a method for surface hardening of 65G steel.
About the Authors
D. R. BaizhanKazakhstan
Daryn Rashituly Baizhan – Senior researcher of scientific research center «Surface engineering and tribology»; PhD student, Educational program 8D05302 «Technical physics»
070002, Kazakhstan, Ust-Kamenogorsk, st. Shakarim, 148
071412, Kazakhstan, Semey, st. Glinki, 20A
G. Erdogan
Turkey
Garip Erdogan – Metallurgical and Materials Engineering Department, Materials Under Extreme Conditions Lab.
54050, Turkey, Sakarya
Т. Alimbekuly
Kazakhstan
Temirlan Alimbekuly – Junior researcher of Scientific Research Center «Surface Engineering and Tribology»; PhD student, Educational program 8D07102 «Mechanical engineering»
070002, Kazakhstan, Ust-Kamenogorsk, st. Shakarim, 148
070000, Kazakhstan, Ust-Kamenogorsk, st. Serikbayev, 19
N. S. Raisov
Kazakhstan
Nurmakhanbet Sayatuly Raisov – junior researcher of Scientific Research Center «Surface Engineering and Tribology»
070002, Kazakhstan, Ust-Kamenogorsk, st. Shakarim, 148
Е. Е. Birzhan
Kazakhstan
Elzhan Erkinuly Birzhan – 4th-year student, Educational Program 6B01509 «Physics and Informatics»
070002, Kazakhstan, Ust-Kamenogorsk, st. Shakarim, 148
References
1. Totten G.E. Steel Heat Treatment: Metallurgy and Technologies / G.E. Totten. – Boca Raton: CRC Press, 2006. – 896 p.
2. Issledovanie izmeneniya struktury, pokazateli tverdosti i treshchinostoikosti plazmennouprochnennoi stali 65G / I.M. Kosanova i dr. // Izvestiya vysshikh uchebnykh zavedenii. Chernaya metallurgiya. – 2023. – Tom 66, № 5. – C. 516-521. https://doi.org/10.17073/0368-0797-2023-5-516-521. (in Russian).
3. Issledovaniya vliyaniya plazmennoi zakalki na protsessy uprochneniya tyazhelonagruzhennykh detalei pochvorezhushchikh mashin / I.M. Kosanova i dr. // Trudy universiteta. – 2023. – № 4(93). – C. 36-42. https://doi.org/10.52209/1609-1825_2023_4_36. (in Russian).
4. Sharifullin S.N. Features of plasma hardening of working bodies of tillage machinery in Kazakhstan / S.N. Sharifullin, A.T. Bainiyazova, M.M. Abzhaev // Bulletin of the Korkyt Ata Kyzylorda University. – 2023. – № 1(1). – P. 15-21. https://doi.org/10.52081/tst.2023.v01.i1.002.
5. Nanoparticle-strengthened-martensitic Surface Layered Constructed Steel by Plasma Hardening Rout / D. Orynbekov et al // Journal of Nanostructures. – 2021. – Vol. 11, № 4. – P. 814-824. https://doi.org/10.22052/JNS.2021.02.018.
6. Tyurin Yu.N. Electric heating using a liquid electrode / Yu.N. Tyurin, A.D. Pogrebnjak // Surface and Coatings Technology. – 2001. – Vol. 142-144. – P. 293-299. https://doi.org/10.1016/S0257-8972(01)01207-5.
7. GOST 14959-2016. Metalloproduktsiya iz ressorno-pruzhinnoi nelegirovannoi i legirovannoi stali. Tekhnicheskie usloviya. – Moskva: Standartinform, 2017. – 28 s. (in Russian).
8. Gulyarenko A. The Method of Calculating Ploughshares Durability in Agricultural Machines Verified on Plasma-Hardened Parts / A. Gulyarenko, M. Bembenek // Agriculture. – 2022. – Vol. 12, № 6. – 841. https://doi.org/10.3390/agriculture12060841.
9. ASTM G99-17; Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus. ASTM International: West Conshohocken, PA, USA, 2016.
10. ISO 13565:1996; Geometrical Product Specifications (GPS) – Surface texture: Profile method; Surfaces having stratified functional properties. ISO: Geneva, Switzerland, 1996.
11. Koval' A.D. Issledovanie kinetiki obrazovaniya nizhnego beinita v strukture vysokouglerodistoi nizkolegirovannoi stali / A.D. Koval', M.N. Brykov, A.E. Kapustyan, D.N. Timofeenko // Novі materіali і tekhnologії v metalurgії ta mashinobuduvannі. – 2011. – (1) – S. 17-21. (in Ukrainian).
Supplementary files
|
1. Неозаглавлен | |
| Subject | ||
| Type | Other | |
Download
(1MB)
|
Indexing metadata ▾ | |
Review
For citations:
Baizhan D.R., Erdogan G., Alimbekuly Т., Raisov N.S., Birzhan Е.Е. EFFECT OF PLASMA HARDENING PARAMETERS ON 65G STEEL STRUCTURE AND PROPERTIES. Bulletin of Shakarim University. Technical Sciences. 2026;(3(23)):741-748. https://doi.org/10.53360/2788-7995-2026-3(23)-74
JATS XML















