4-санға «Автоматтандыру және ақпараттық технологиялар», «Азық-түлік инженериясы және биотехнология», сондай-ақ «Химиялық технология» бағыттары бойынша мақалалар қабылдау жабылды.

Приём статей в четвёртый номер по направлениям «Автоматизация и информационные технологии», «Пищевая инженерия и биотехнология», а также «Химическая технология» закрыт.

Submissions for the fourth issue in the fields of Automation and Information Technology, Food Engineering and Biotechnology, as well as Chemical Technology, are now closed.

Preview

Bulletin of Shakarim University. Technical Sciences

Bulletin of Shakarim University. Technical Sciences

Advanced search

MATHEMATICAL MODELING OF THE FINE GRINDING PROCESS OF MEAT-AND-BONE RAW MATERIALS

https://doi.org/10.53360/2788-7995-2026-3(23)-59

Abstract

Fine grinding sets the dispersion of the raw material and, through it, the structure and waterbinding capacity of the minced mass, yet in conventional lines it is separated from preliminary grinding, which increases the number of machines and the specific energy demand. The article presents a mathematical model of the fine grinding of meat-and-bone raw materials in a combined unit where both stages run sequentially in one working space from a single drive. The model is built on the Bingham rheological body supplemented by an element describing the instantaneous irreversible deformation of bone inclusions, and is arranged as two series-connected contours. Summation of the contour shear rates gives a compact equation with equivalent (reduced) characteristics, coupled with the kinematics of the cutting mechanism, so that the power of the process is expressed through yield shear stress, cutting area, blade radius and rotational speed. Adequacy was verified against yield shear stress measured by penetration in eight runs with three replications: the calculated Fi = 0.29164 is lower than the tabulated Ftab = 1.02 at f1 = 3, f2 = 4, α = 0.1. At 16.7 s⁻ ¹ the combined unit reached 151.3 kg/h against 96.3 kg/h, 68 % of particles fell within 100–150 μm against 36 %, and specific energy consumption decreased from 31.15 to 22.14 kW·h/t.

About the Authors

G. B. Bekeshova
L.N. Gumilyov Eurasian National University
Kazakhstan

Gulvira Bauyrzhanovna Bekeshova – Master of Technical Sciences, Senior Lecturer of the Department of Information Security, Faculty of Information Technologies

010008, Republic of Kazakhstan, Astana, st. Satpayev, 2



N. K. Ibragimov
Shakarim University
Kazakhstan

Nadir Kadyrovich Ibragimov – Candidate of Technical Sciences

071412, Republic of Kazakhstan, Semey, st. Glinka, 20 A



B. A. Lobasenko
Kemerovo State University
Russian Federation

Boris Anatolyevich Lobasenko – Doctor of Technical Sciences, Professor

650000, Russian Federation, Kemerovo, st. Krasnaya, 6



References

1. Rogov I.A. Obshchaya tekhnologiya myasa i myasoproduktov [General technology of meat and meat products]: textbook / I.A. Rogov, A.G. Zabashta, G.P. Kazyulin. – Moscow: Kolos, 2000. – 367 p. (in Russian).

2. A review on the relation between grinding process and quality of ground meat / L.M. Berger et al // Meat Science. – 2023. – Vol. 205. – Art. 109320. https://doi.org/10.1016/j.meatsci.2023.109320.

3. Development of the design of plate with variable diameters of holes and its impact on meatgrinding quality and efficiency / A. Bakiyeva et al // Processes. – 2024. – Vol. 12, № 9. – Art. 1808. https://doi.org/10.3390/pr12091808.

4. Development and evaluation of modified rotor–stator knives for enhanced fine grinding of chicken meat–bone raw material in colloid mill / Z. Yessimbekov et al // Applied Sciences. – 2025. – Vol. 15, № 13. – Art. 7106. https://doi.org/10.3390/app15137106.

5. Effect of rotational speed and gap between rotating knives of the grinder on the yield stress and water-binding capacity of fine ground chicken bone / G. Bekeshova et al // Applied Sciences. – 2022. – Vol. 12, № 7. – Art. 3533. https://doi.org/10.3390/app12073533.

6. Grudanov V.Ya. Primenenie teorii chisel v konstruirovanii rezhushchikh mekhanizmov mashin dlya izmelcheniya myasnogo syrya [Application of number theory in the design of cutting mechanisms of machines for grinding meat raw materials] / V.Ya. Grudanov, A.A. Brench, L.T. Tkacheva // Aktualnye voprosy pererabotki myasnogo i molochnogo syrya. – 2021. – № 11. – P. 144-154. (in Russian).

7. Opportunities and perspectives for utilisation of co-products in the meat industry / S.A. Lynch et al // Meat Science. – 2018. – Vol. 144. – P. 62-73. https://doi.org/10.1016/j.meatsci.2018.06.019.

8. Optimising the use of proteins from rich meat co-products and non-meat alternatives: nutritional, technological and allergenicity challenges / C. Anzani et al // Food Research International. – 2020. – Vol. 137. – Art. 109575. https://doi.org/10.1016/j.foodres.2020.109575.

9. Gorbatov A.V. Reologiya myasnykh i molochnykh produktov [Rheology of meat and dairy products] / A.V. Gorbatov. – Moscow: Pishchevaya promyshlennost, 1979. – 384 p. (in Russian).

10. Martínez-Padilla L.P. Rheology of liquid foods under shear flow conditions: recently used models / L.P. Martínez-Padilla // Journal of Texture Studies. – 2024. – Vol. 55, № 1. – Art. e12802. https://doi.org/10.1111/jtxs.12802.

11. Reologiya: textbook / E.V. Zakipnaya et al. – Blagoveshchensk: Far Eastern State Agrarian University Publishing House, 2015. – 108 p. (in Russian).

12. Takabi B. A review of cutting mechanics and modeling techniques for biological materials / B. Takabi, B.L. Tai // Medical Engineering & Physics. – 2017. – Vol. 45. – P. 1-14. https://doi.org/10.1016/j.medengphy.2017.04.004.

13. Antipova L.V. Metody issledovaniya myasa i myasnykh produktov [Methods for studying meat and meat products]: textbook / L.V. Antipova, I.A. Glotova, I.A. Rogov. – Moscow: Kolos, 2001. – 376 p. (in Russian).

14. Developing new type of disk plate for meat chopper and its effect to water-binding capacity and yield stress of minced meat / A. Bakieva et al // International Journal of Mechanical and Production Engineering Research and Development. – 2019. – Vol. 9, № 6. – P. 377-390.

15. Thermal image processing technique for determination of temperature distributions of minced beef thawed by ohmic and conventional methods / D. Döner et al // Food and Bioprocess Technology. – 2020. – Vol. 13, № 11. – P. 1878-1892. https://doi.org/10.1007/s11947-020-02530-w.


Review

For citations:


Bekeshova G.B., Ibragimov N.K., Lobasenko B.A. MATHEMATICAL MODELING OF THE FINE GRINDING PROCESS OF MEAT-AND-BONE RAW MATERIALS. Bulletin of Shakarim University. Technical Sciences. 2026;(3(23)):593-600. https://doi.org/10.53360/2788-7995-2026-3(23)-59

Views: 12

JATS XML


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2788-7995 (Print)
ISSN 3006-0524 (Online)
X