DETERMINATION OF THE OPTIMAL FILLING DEGREE OF A CEMENT COMPOUND WITH A SIMULANT OF SOLID RADIOACTIVE WASTE FOR RADIOACTIVE WASTE IMMOBILIZATION
https://doi.org/10.53360/2788-7995-2026-3(23)-71
Abstract
Safe conditioning and long-term storage of solid radioactive waste are among the key challenges associated with the decommissioning of nuclear facilities. The aim of this study was to determine the optimal filling degree of a cement matrix using a solid radioactive waste simulant representing waste generated during the decommissioning of the BN-350 reactor. Cement compounds containing 15, 25, and 40 wt.% of the solid radioactive waste simulant were prepared and investigated. The physicomechanical properties of the samples were evaluated through microhardness measurements, compressive strength testing, and analysis of fracture behavior. The results demonstrated that the simulant content has a significant effect on the structural state and mechanical performance of the cement compounds. The highest values of microhardness and compressive strength were obtained for the composition containing 15 wt.% simulant, indicating the formation of a more homogeneous and mechanically durable cement matrix. Increasing the simulant content to 25 wt.% resulted in a moderate decrease in mechanical properties; however, the obtained values remained within the range required for cemented radioactive waste forms. At a simulant content of 40 wt.%, a substantial reduction in mechanical strength and deterioration of the structural integrity of the cement compound were observed. The obtained results can be used for optimizing the composition of cement matrices intended for the immobilization of solid radioactive waste and for improving the efficiency of radioactive waste conditioning technologies.
About the Authors
N. MukhamedovKazakhstan
Nurzhan Mukhamedov – PhD, Associate Professor, Head of Department, Institute of Atomic Energy
180010, Republic of Kazakhstan, Kurchatov, Beybit Atom St. 10
071412, Republic of Kazakhstan, Semey, 20 A Glinka Street
O. Oken
Kazakhstan
Ospan Oken – Engineer, Laboratory of Advanced Materials, Institute of Atomic Energy
180010, Republic of Kazakhstan, Kurchatov, Beybit Atom St. 10
S. Dolzhikov
Kazakhstan
Sergey Dolzhikov – Head of Laboratory Group, Institute of Atomic Energy
180010, Republic of Kazakhstan, Kurchatov, Beybit Atom St. 10
071412, Republic of Kazakhstan, Semey, 20 A Glinka Street
D. M. Seken
Kazakhstan
Darkhan Seken – Engineer, Institute of Atomic Energy
180010, Republic of Kazakhstan, Kurchatov, Beybit Atom St. 10
071412, Republic of Kazakhstan, Semey, 20 A Glinka Street
A. Raiko
Kazakhstan
Anel Raiko – Engineer, Institute of Atomic Energy
180010, Republic of Kazakhstan, Kurchatov, Beybit Atom St. 10
References
1. International Atomic Energy Agency. Classification of Radioactive Waste // IAEA Safety Standards Series No. GSG-1. – Vienna: IAEA. – 2009.
2. International Atomic Energy Agency. Predisposal Management of Radioactive Waste // IAEA Safety Standards Series No. GSR Part 5. – Vienna: IAEA. – 2009.
3. International Atomic Energy Agency. Disposal of Radioactive Waste // IAEA Safety Standards Series № SSR-5. – Vienna: IAEA. – 2011.
4. International Atomic Energy Agency. Development of Waste Acceptance Criteria for Low and Intermediate Level Radioactive Waste // IAEA Nuclear Energy Series No. NW-T-1.29. – Vienna: IAEA. – 2025.
5. Li J. Solidification of radioactive wastes by cement-based materials / J. Li, L. Chen, J. Wang // Progress in Nuclear Energy. 2021.– V.141. https://doi.org/10.1016/j.pnucene.2021.103957.
6. Byeon J. Statistical analysis of effects of test conditions on compressive strength of cement solidified radioactive waste / J. Byeon, S. Park // Nuclear Engineering and Technology. – 2023. – № 55(3). – P. 876-883. https://doi.org/10.1016/j.net.2022.11.008.
7. Cementitious Materials for Nuclear Waste Immobilization / R.O. Abdel Rahman et al // Chichester: John Wiley & Sons. – 2015. https://doi.org/10.1002/9781118511992.
8. Abdel Rahman R.O. Toward Sustainable Cementitious Radioactive Waste Forms: Immobilization of Problematic Operational Wastes / R.O. Abdel Rahman, M.I. Ojovan // Sustainability. – 2021. – № 13(21). – 11992. https://doi.org/10.3390/su132111992.
9. Ojovan M.I. An Introduction to Nuclear Waste Immobilisation / M.I. Ojovan, W.E. Lee. – Elsevier, 2nd ed.: 2013. – ISBN 9780080993935.
10. Pilania R.K., Dube C.L. Matrices for Radioactive Waste Immobilization: A Review // Frontiers in Materials. – 2023. – Vol. 10. https://doi.org/10.3389/fmats.2023.1236470.
11. I,Luhar, S.Luhar, M.Abdullah, A.Sandu et.al. Solidification/Stabilization Technology for Radioactive Wastes Using Cement: An Appraisal // Materials. – 2023. – Vol.16(3). – https://doi.org/10.3390/ma16030954.
12. Advances in immobilization of radionuclide wastes by alkali-activated cement and related materials / Y. Zhu et al // Cement and Concrete Composites. – 2022. – Vol. 126. https://doi.org/10.1016/j.cemconcomp.2021.104377.
13. Decommissioning of the BN-350 fast neutron reactor: history review and current status / N. Mukhamedov et al // Energies.– Vol. 18. – 2025. https://doi.org/10.3390/en18133486.
14. The BN-350 reactor decommissioning: quantitative analysis and prospects for solid radioactive waste management / N. Mukhamedov et al // Energies. – Vol. 18(17). – 2025. https://doi.org/10.3390/en18174651.
15. Sorption-thermal immobilization of salt-bearing liquid radioactive waste via spark plasma sintering of perlite / V. Baklanov et al // Nuclear Engineering and Design. – 2026. – Vol. 415. – Article 115051. https://doi.org/10.1016/j.nucengdes.2026.115051.
16. Semey Cement Plant. (n.d.). Production. https://semeycement.com/production/.
17. Federal Agency on Technical Regulating and Metrology. (2020). GOST 31108-2020. Common cements. Specifications. Standartinform.
18. ASTM International. (2022). ASTM E384 22: Standard Test Method for Microindentation Hardness of Materials. West Conshohocken, PA, USA: ASTM International. Retrieved from https://store.astm.org/e0384-22.html.
19. ASTM C39/C39M-26. Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens. ASTM International, West Conshohocken, PA, USA, 2026.
Review
For citations:
Mukhamedov N., Oken O., Dolzhikov S., Seken D.M., Raiko A. DETERMINATION OF THE OPTIMAL FILLING DEGREE OF A CEMENT COMPOUND WITH A SIMULANT OF SOLID RADIOACTIVE WASTE FOR RADIOACTIVE WASTE IMMOBILIZATION. Bulletin of Shakarim University. Technical Sciences. 2026;(3(23)):715-722. (In Kazakh) https://doi.org/10.53360/2788-7995-2026-3(23)-71
JATS XML















