4-санға «Автоматтандыру және ақпараттық технологиялар», «Азық-түлік инженериясы және биотехнология», сондай-ақ «Химиялық технология» бағыттары бойынша мақалалар қабылдау жабылды.

Приём статей в четвёртый номер по направлениям «Автоматизация и информационные технологии», «Пищевая инженерия и биотехнология», а также «Химическая технология» закрыт.

Submissions for the fourth issue in the fields of Automation and Information Technology, Food Engineering and Biotechnology, as well as Chemical Technology, are now closed.

Preview

Bulletin of Shakarim University. Technical Sciences

Bulletin of Shakarim University. Technical Sciences

Advanced search

DETERMINATION OF LOAD CHARACTERISTICS AND DESIGN OF A PNEUMATIC MOTOR AS PART OF A COMPRESSED AIR ENERGY STORAGE SYSTEM

https://doi.org/10.53360/2788-7995-2026-3(23)-34

Abstract

This paper presents the results of a study on the load characteristics of a jet-type reaction pneumatic motor powered by compressed air. The design features of a two-stage motor are considered, in which energy conversion is achieved through the reaction force of the air jet and the pressure exerted by the expanding compressed air on the rotor blades. The operating principle of the device is described, including the processes of air supply, distribution, expansion, and exhaust of the working medium. To evaluate the operational characteristics, mathematical modeling was carried out in the MATLAB/Simulink environment. The influence of inlet pressure on the main performance parameters of the pneumatic motor, including output power, rotational speed, angular velocity, and torque, was analyzed. The results show that increasing the inlet pressure leads to a steady increase in all investigated parameters. The most pronounced dependence was observed for output power and rotational speed, confirming the possibility of controlling the operating modes by varying the supply air pressure. The increase in torque is attributed to the higher reaction force generated by the air jet and the enhanced effect of the expanding air on the rotor blades. The obtained results make it possible to evaluate the operability of the proposed design and the variation of its performance over a wide pressure range. These findings can be applied to the design of pneumatic motors, the selection of optimal operating conditions, and serve as a basis for further experimental investigations.

About the Authors

E. T. Abilmazhinov
Shakarim University
Kazakhstan

Yermek Tolegenovich Abilmazhinov – Doctor of Technical Sciences, Professor of the Department of Automation and Information Technologies

20A Glinki St., Semey 071412, Republic of Kazakhstan



E. Ya. Shayakhmetov
Shakarim University
Kazakhstan

Yerzhan Shayakhmetov – PhD, «Automation and Information Technologies» 

 20A Glinki St., Semey 071412, Republic of Kazakhstan 



D. K. Dukenbaev
Shakarim University
Kazakhstan

Damir Kairatovich Dukenbaev – doctoral student of the Department of Bioengineering Systems

 20A Glinki St., Semey 071412, Republic of Kazakhstan 



R. A. Sovetbayev
Shakarim University
Kazakhstan

Rail Ayanovich Sovetbayev – PhD, «Automation and Information Technologies»

 20A Glinki St., Semey 071412, Republic of Kazakhstan 



V. N. Kots
Shakarim University
Kazakhstan

Vladislav Nikolaevich Kots – Master of Technical Sciences in Mechanical Engineering; Researcher at the Engineering Center

20A Glinki St., Semey 071412, Republic of Kazakhstan



References

1. Pnevmaticheskii privod gornykh mashin / A.V. Ivanov i dr. – Moskva: TSINTIAM, 1963. – 58 s. (in Russian).

2. Beater P. Pneumatic drives: system design, modelling and control / P. Beater. – Berlin: Springer-Verlag, 2007. – 323 p. (in English).

3. Majumdar S.R. Pneumatic systems: principles and maintenance / S.R. Majumdar. – New Delhi: Tata McGraw-Hill, 1996. – 282 p. (in English).

4. Control performance of an air motor: can air motors replace electric motors? / S.R. Pandian et al // Proceedings of the 1999 IEEE International Conference on Robotics and Automation. – 1999. – Vol. 1. – P. 518-524. https://doi.org/10.1109/ROBOT.1999.770029. (in English).

5. Kaliev A.K. Analiz rabochikh protsessov plastinchatogo pnevmomotora s uchetom utechek rabochego tela / A.K. Kaliev, R.T. Smagulov // Vestnik mashinostroeniya. – 2021. – № 5. – S. 34-39. (in Russian).

6. Modeling and analysis of a novel rotary pneumatic motor with symmetric multi-cylinder / Y. Xing et al // Chinese Journal of Mechanical Engineering. – 2019. – Vol. 32, № 1. – Art. 15. (in English).

7. Beater P. Modelling and control of pneumatic vane motors / P. Beater // International Journal of Fluid Power. – 2004. – Vol. 5, № 1. – P. 7-16. (in English).

8. DEPRAG SCHULZ GMBH & CO. KG. Air motors: product catalog [Electronic resource]. – Amberg: DEPRAG, 2024. (in English).

9. Gast Manufacturing, Inc. Air motors/gearmotors: product catalog [Electronic resource]. – Benton Harbor: Gast Manufacturing, 2018. (in English).

10. Atlas Copco. Air motors LZB/LZL: product catalogue [Electronic resource]. – Stockholm: Atlas Copco Industrial Technique, 2024. (in English).

11. Patent № 32403 Respublika Kazakhstan, MPK ne ukazan. Rotornaya mashina / S.M. Anibaev, A.Zh. Akimzhanov; zayavitel' i patentoobladatel' ne ukazany. – Zayavl. 10.03.2016; opubl. 29.09.2017. (in Russian).


Review

For citations:


Abilmazhinov E.T., Shayakhmetov E.Ya., Dukenbaev D.K., Sovetbayev R.A., Kots V.N. DETERMINATION OF LOAD CHARACTERISTICS AND DESIGN OF A PNEUMATIC MOTOR AS PART OF A COMPRESSED AIR ENERGY STORAGE SYSTEM. Bulletin of Shakarim University. Technical Sciences. 2026;(3(23)):362-368. (In Russ.) https://doi.org/10.53360/2788-7995-2026-3(23)-34

Views: 11

JATS XML


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2788-7995 (Print)
ISSN 3006-0524 (Online)
X