4-санға «Автоматтандыру және ақпараттық технологиялар», «Азық-түлік инженериясы және биотехнология», сондай-ақ «Химиялық технология» бағыттары бойынша мақалалар қабылдау жабылды.

Приём статей в четвёртый номер по направлениям «Автоматизация и информационные технологии», «Пищевая инженерия и биотехнология», а также «Химическая технология» закрыт.

Submissions for the fourth issue in the fields of Automation and Information Technology, Food Engineering and Biotechnology, as well as Chemical Technology, are now closed.

Preview

Bulletin of Shakarim University. Technical Sciences

Bulletin of Shakarim University. Technical Sciences

Advanced search

INFLUENCE OF PROTECTIVE COATING ON THE MECHANICAL AND TRIBOLOGICAL PERFORMANCE OF CEMENTED CARBIDE TURNING INSERTS

https://doi.org/10.53360/2788-7995-2026-3(23)-68

Abstract

This study presents a comprehensive comparative evaluation of the performance characteristics of commercial coated cemented carbide turning inserts of different grades after turning operations. The wear mechanisms of the cutting edge were investigated using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). In addition, the mechanical properties of the coatings, including microhardness and elastic modulus, were determined by instrumented indentation, while their adhesion strength was evaluated using the progressive scratch test. The results revealed that the coating failure was governed by a combination of abrasive and adhesive wear mechanisms, accompanied by localized edge chipping, crater formation, and material transfer from the workpiece onto the tool surface. The highest microhardness values (2258-2261 HV) were obtained for the YBC252 series inserts, which correlated with a lower degree of coating degradation after machining. Scratch test results demonstrated that coatings with higher hardness exhibited greater resistance to mechanical failure and superior adhesion strength. The comprehensive analysis established a clear relationship between the mechanical properties of the coatings, their wear mechanisms, and the service performance of commercial cemented carbide turning inserts.

About the Authors

Zh. B. Sagdoldina
Sarsen Amanzholov East Kazakhstan University
Kazakhstan

Zhuldyz Bolatkyzy Sagdoldina – PhD, Associate Professor, Senior Researcher of Scientific Research Center «Surface Engineering and Tribology» 

070002, Kazakhstan, Ust-Kamenogorsk, st. Shakarima 148



D. B. Buitkenov
Sarsen Amanzholov East Kazakhstan University
Kazakhstan

Dastan Bolatuly Buitkenov – PhD, Leading Researcher of Scientific Research Center «Surface Engineering and Tribology»

070002, Kazakhstan, Ust-Kamenogorsk, st. Shakarima 148



M. M. Ezhembaev
Sarsen Amanzholov East Kazakhstan University
Kazakhstan

Medet Malikovich Ezhembaev – Master's student

070002, Kazakhstan, Ust-Kamenogorsk, st. Shakarima 148



N. N. Yusof
School of Physics, Universiti Sains Malaysia
Malaysia

Nur Nabihah Yusof – PhD, Associate Professor at School of Physics

11800, USM, Penang, Malaysia



A. B. Nabioldina
Sarsen Amanzholov East Kazakhstan University
Kazakhstan

Aiym Bauyrzhanqyzy Nabioldina – Senior research Scientific Research Center «Surface Engineering and Tribology»

070002, Kazakhstan, Ust-Kamenogorsk, st. Shakarima 148 



References

1. Gassner M. Hard coatings on cemented carbide cutting tools: process technology and application: dissertation / M. Gassner. – Leoben: Montanuniversität Leoben, 2018.

2. Revuru R.S. Performance of coated cutting tools in machining: a review / R.S. Revuru, V.K. Pasam, N.R. Posinasetti // Proceedings of the International Conference on Emerging Trends in Engineering & Technology (IConETech-2020). – 2020. – P. 792-802. https://doi.org/10.47412/JSID9445.

3. Machining GX2CrNiMoN26-7-4 DSS alloy: wear analysis of TiAlN and TiCN/Al₂O₃/TiN coated carbide tools behavior in rough end milling operations / F.J.G. Silva et al // Coatings. – 2019. – Vol. 9, № 6. – Art. 392. https://doi.org/10.3390/coatings9060392.

4. Investigation of coated and uncoated carbide cutting tool wear in dry turning of EN AW 2007 aluminum alloy / K. Leksycki et al // International Journal of Applied Mechanics and Engineering. – 2024. – Vol. 29, № 3. – P. 69-81. https://doi.org/10.59441/ijame/190057.

5. Structural changes in Ti₁₋ₓAlₓN coatings during turning: a XANES and EXAFS study of worn tools / L. Rogström et al // Applied Surface Science. – 2023. – Vol. 612. – Art. 155907. https://doi.org/10.1016/j.apsusc.2022.155907.

6. Jaafar T. Characterization of TiCN and TiCN/ZrN coatings for cutting tool application / T. Jaafar // Ceramics International. – 2013. https://doi.org/10.1016/j.ceramint.2012.07.061.

7. Sahoo S.P. Comparative experimental study on application feasibility of MTCVD TiCN–Al₂O₃–TiOCN multilayer-coated carbide and PVD TiN single-layer-coated composite ceramic inserts during dry machining of Ti–6Al–4V / S.P. Sahoo, S. Datta // Sādhanā. – 2022. – Vol. 47, № 2. – Art. 105. https://doi.org/10.1007/s12046-022-01880-9.

8. Cutting with coated tools: coating technologies, characterization methods and performance optimization / K.-D. Bouzakis et al // CIRP Annals – Manufacturing Technology. – 2012. – Vol. 61, № 2. – P. 703-723. https://doi.org/10.1016/j.cirp.2012.05.006.

9. Boing D. Evaluation of wear mechanisms of PVD and CVD coatings deposited on cemented carbide substrates applied to hard turning / D. Boing, A.J. de Oliveira, R.B. Schroeter // The International Journal of Advanced Manufacturing Technology. – 2020. – Vol. 106. – P. 5441-5451. https://doi.org/10.1007/s00170-020-05000-x.

10. Chinchanikar S., Choudhury S. K. Wear behaviors of single-layer and multilayer-coated carbide inserts in high-speed machining of hardened AISI 4340 steel / S. Chinchanikar, S.K. Choudhury // Journal of Mechanical Science and Technology. – 2013. – Vol. 27. – P. 1451-1459. https://doi.org/10.1007/s12206-013-0325-2.


Review

For citations:


Sagdoldina Zh.B., Buitkenov D.B., Ezhembaev M.M., Yusof N.N., Nabioldina A.B. INFLUENCE OF PROTECTIVE COATING ON THE MECHANICAL AND TRIBOLOGICAL PERFORMANCE OF CEMENTED CARBIDE TURNING INSERTS. Bulletin of Shakarim University. Technical Sciences. 2026;(3(23)):679-686. https://doi.org/10.53360/2788-7995-2026-3(23)-68

Views: 14

JATS XML


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2788-7995 (Print)
ISSN 3006-0524 (Online)
X