Төртінші нөмірге барлық бағыттар бойынша мақалалар қабылдау аяқталды.

Приём статей в четвёртый номер по всем направлениям закрыт.

Submissions for the fourth issue are now closed across all subject areas.

Preview

Вестник Университета Шакарима. Серия технические науки

Вестник Университета Шакарима. Серия технические науки

Расширенный поиск

ГИДРОДИНАМИЧЕСКИЕ И ТЕПЛОФИЗИЧЕСКИЕ АСПЕКТЫ ОПТИМИЗАЦИИ ОРОСИТЕЛЬНЫХ УСТРОЙСТВ В ТЕХНИЧЕСКИХ СИСТЕМАХ РАСПЫЛЕНИЯ: ОБЗОР

https://doi.org/10.53360/2788-7995-2026-3(23)-65

Аннотация

В статье представлен обзор современных исследований, посвящённых гидродинамическим и теплофизическим аспектам работы оросительных и распылительных устройств в технических системах. Цель работы заключается в систематизации научных представлений о влиянии конструктивных, режимных и теплофизических параметров сопел на формирование распылённого потока, равномерность орошения и эффективность тепло- и массообмена. Рассмотрены основные типы оросительных устройств, включая струйные, веерные, конусные, центробежные и пневматические распылители. Проанализировано влияние рабочего давления, расхода жидкости, геометрии проточной части, размера и скорости капель, угла раскрытия факела, плотности орошения и свойств рабочей среды на структуру капельного потока. Показано, что эффективность оросительных устройств определяется не только расходной характеристикой и давлением, но и рациональным сочетанием дисперсности распыла, устойчивости факела, равномерности распределения жидкости и условий взаимодействия капель с газовой средой, насадкой или теплообменной поверхностью. Особое внимание уделено распылительному охлаждению, где ключевое значение имеют капельный спектр, положение сопла, состояние поверхности, режим кипения и критический тепловой поток. Для градирен и испарительных систем выделена роль равномерного водораспределения как одного из определяющих факторов эффективности тепло- и массообмена. Рассмотрены возможности CFD-моделирования для анализа внутреннего течения в соплах, закручивания потока, формирования жидкой плёнки и структуры факела распыла. Сделан вывод о необходимости комплексного учёта гидродинамических, теплофизических и эксплуатационных параметров при проектировании и оптимизации оросительных устройств для градирен, испарительных охладителей, аппаратов газоочистки и установок распылительного охлаждения.

Об авторах

А. А. Ахметов
Шәкәрім университет
Казахстан

Алихан Алибекович Ахметов – докторант образовательной программы 8D05302-«Техническая физика» кафедры «Техническая физика и теплоэнергетика»

071412, Республика Казахстан, г. Семей, ул. Глинки, 20 А



М. В. Ермоленко
Шәкәрім университет
Казахстан
Михаил Вячеславович Ермоленко – к.т.н., ассоциированный профессор, старший преподаватель кафедры «Техническая физика и теплоэнергетика»

071412, Республика Казахстан, г. Семей, ул. Глинки, 20 А



О. А. Степанова
Шәкәрім университет
Казахстан

Ольга Александровна Степанова – кандидат технических наук, профессор, заведующая кафедрой «Техническая физика и теплоэнергетика»

071412, Республика Казахстан, г. Семей, ул. Глинки, 20 А



Список литературы

1. Lefebvre A.H. Atomization and Sprays / A.H. Lefebvre, V.G. McDonell. – 2nd ed. Boca Raton: CRC Press, 2017. https://www.routledge.com/Atomization-and-Sprays/LefebvreMcDonell/p/book/9781498736251.

2. Handbook of Atomization and Sprays: Theory and Applications / N. Ashgriz et al. – New York: Springer, 2011. https://doi.org/10.1007/978-1-4419-7264-4.

3. Nasr G.G. Industrial Sprays and Atomization: Design, Analysis and Applications / G.G. Nasr, A.J. Yule, L. Bendig. London: Springer, 2002. https://doi.org/10.1007/978-1-4471-3816-7.

4. Bayvel L. Liquid Atomization / L. Bayvel, Z. Orzechowski/ Washington: Taylor & Francis, 1993. https://www.routledge.com/Liquid-Atomization/Bayvel/p/book/9780891169598.

5. Sirignano W.A. Fluid Dynamics and Transport of Droplets and Sprays / W.A. Sirignano. 2nd ed. Cambridge: Cambridge University Press, 2010. https://www.cambridge.org/.

6. Multiphase Flows with Droplets and Particles / C.T. Crowe et al. 2nd ed. Boca Raton: CRC Press, 2011. https://www.routledge.com/Multiphase-Flows-with-Droplets-and-Particles/CroweSchwarzkopf-Sommerfeld-Tsuji/p/book/9781439840504.

7. Yarin A.L. Drop impact dynamics: splashing, spreading, receding, bouncing / A.L. Yarin // Annual Review of Fluid Mechanics. – 2006. – Vol. 38. – P. 159-192. https://doi.org/10.1146/annurev.fluid.38.050304.092144.

8. Rein M. Phenomena of liquid drop impact on solid and liquid surfaces / M. Rein // Fluid Dynamics Research. – 1993. – Vol. 12, № 2. – P. 61-93. https://doi.org/10.1016/0169-5983(93)90106-K.

9. Experimental investigations of spray characteristics of a pressure-swirl atomizer / X. Fan et al // Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy. – 2020. – Vol. 234, № 5. https://doi.org/10.1177/0957650919875612.

10. Experimental investigation of flat fan nozzle V-cut depths and its impact on spray characteristics / W. Mughal et al // Scientific Reports. – 2025. – Vol. 15. – Article 22959. https://doi.org/10.1038/s41598-025-05319-z.

11. Mondal D. Droplet size and velocity distributions in a spray from a pressure swirl atomizer: application of maximum entropy formalism / D. Mondal, A. Datta, A. Sarkar // Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. – 2004. – Vol. 218, № 7. – P. 737-749. https://doi.org/10.1243/0954406041319563.

12. Droplet spectrum of standard flat fan and hollow cone spray nozzles / J.P.A.R. Cunha et al // Pesquisa Agropecuária Brasileira. – 2004. – Vol. 39, № 10. – P. 977-985. https://apct.sede.embrapa.br/pab/article/view/6865.

13. ISO 5682-1:2017. Equipment for crop protection – Spraying equipment – Part 1: Test methods for sprayer nozzles. Geneva: International Organization for Standardization, 2017. https://www.iso.org/standard/60053.html.

14. ISO 25358:2018. Crop protection equipment – Droplet-size spectra from atomizers – Measurement and classification. Geneva: International Organization for Standardization, 2018. https://www.iso.org/.

15. ANSI/ASABE S572.3. Spray Nozzle Classification by Droplet Spectra. St. Joseph, MI: American Society of Agricultural and Biological Engineers, 2020. URL: https://elibrary.asabe.org/azdez.asp?AID=51101.

16. Miller P.C.H. Evaluation of a spray nozzle patternator / P.C.H. Miller // Journal of Agricultural Engineering Research. – 1986. – № 1. – P. 43-52. https://doi.org/10.1016/0261-2194(86)90032-3.

17. Laser Doppler and Phase Doppler Measurement Techniques / H.-E. Albrecht et al. Berlin: Springer, 2003. https://doi.org/10.1007/978-3-662-05165-8.

18. Effect of nozzle type, size and pressure on spray droplet characteristics / D. Nuyttens et al // Biosystems Engineering. – 2007. – Vol. 97, № 3. – P. 333-345. https://doi.org/10.1016/j.biosystemseng.2007.03.001.

19. Reducing ground and airborne drift losses in young apple orchards with PWM-controlled spray systems / R. Salcedo et al // Computers and Electronics in Agriculture. – 2021. – Vol. 184. – Article 106389. https://doi.org/10.1016/j.compag.2021.106389.

20. Characterization of activation pressure, flow rate and spray angle for PWM-controlled hollowcone nozzles / R. Salcedo et al // Biosystems Engineering. – 2022. – Vol. 218. – P. 139-152. https://doi.org/10.1016/j.biosystemseng.2022.04.002.

21. Effect of angled spray nozzle designs on spray distribution and droplet spectrum / M.M. Negrisoli et al // Revista Ciência Agronômica. – 2021. – Vol. 52, № 3. https://www.scielo.br/j/rca/a/3YNNjbRVPPQmDk8dPyHTD3f/.

22. Czaczyk Z. Spray classification for selected flat fan nozzles / Z. Czaczyk // Journal of Plant Protection Research. – 2012. – Vol. 52, № 1. https://www.plantprotection.pl/Spray-classification-forselected-flat-fan-nozzles,91811,0,2.html.

23. The international (BCPC) spray classification system including a drift potential factor / E.S.E. Southcombe et al // Proceedings of the Brighton Crop Protection Conference – Weeds. – 1997. – P. 371-380.

24. Spillman J.J. Spray impaction, retention and adhesion: an introduction to basic characteristics / J.J. Spillman // Pesticide Science. – 1984. – Vol. 15, № 2. – P. 97-106. https://doi.org/10.1002/ps.2780150202.

25. Hewitt A.J. Spray drift: impact of requirements to protect the environment / A.J. Hewitt // Crop Protection. – 2000. – Vol. 19, № 8-10. – P. 623-627. https://doi.org/10.1016/S0261-2194(00)00082-X.

26. Gaillard A. What determines the drop size in sprays of polymer solutions? / A. Gaillard, R. Sijs, D. Bonn // arXiv. 2021. https://arxiv.org/abs/2108.11163.

27. Kim J. Spray cooling heat transfer: the state of the art / J. Kim // International Journal of Heat and Fluid Flow. – 2007. – Vol. 28, № 4. – P. 753-767. https://doi.org/10.1016/j.ijheatfluidflow.2006.09.003.

28. Spray cooling and flash evaporation cooling: the current development and application / W.-L. Cheng et al // Renewable and Sustainable Energy Reviews. – 2016. – Vol. 55. – P. 614-628. https://doi.org/10.1016/j.rser.2015.11.014.

29. Liang G. Review of spray cooling – Part 1: Single-phase and nucleate boiling regimes, and critical heat flux / G. Liang, I. Mudawar // International Journal of Heat and Mass Transfer. – 2017. – Vol. 115. – P. 1174-1205. https://doi.org/10.1016/j.ijheatmasstransfer.2017.06.029.

30. Liang G. Review of spray cooling - Part 2: High temperature boiling regimes and quenching applications / G. Liang, I. Mudawar // International Journal of Heat and Mass Transfer. – 2017. – Vol. 115. – P. 1206-1222. https://doi.org/10.1016/j.ijheatmasstransfer.2017.06.030.

31. Horacek B. Single nozzle spray cooling heat transfer mechanisms / B. Horacek, K.T. Kiger, J. Kim // International Journal of Heat and Mass Transfer. – 2005. – Vol. 48, № 8. – P. 1425-1438. https://doi.org/10.1016/j.ijheatmasstransfer.2004.10.026.

32. Rybicki J.R. Single-phase and two-phase cooling characteristics of upward-facing and downward-facing sprays / J.R. Rybicki, I. Mudawar // International Journal of Heat and Mass Transfer. – 2006. – Vol. 49, № 1-2. P. 5-16. https://engineering.purdue.edu/mudawar/files/articlesall/2006/2006-01.pdf.

33. Estes K.A. Correlation of Sauter mean diameter and critical heat flux for spray cooling of small surfaces / K.A. Estes, I. Mudawar // International Journal of Heat and Mass Transfer. – 1995. – Vol. 38, № 16. – P. 2985-2996. https://doi.org/10.1016/0017-9310(95)00047-C.

34. Mudawar I. Assessment of high-heat-flux thermal management schemes / I. Mudawar // IEEE Transactions on Components and Packaging Technologies. – 2001. – Vol. 24, № 2. – P. 122-141. https://doi.org/10.1109/6144.926375.

35. Spray cooling as a high-efficient thermal management solution: a review / J. Yin et al // Energies. – 2022. – Vol. 15, № 22. – Article 8547. https://doi.org/10.3390/en15228547.

36. Heat transfer during multiple droplet impingement and spray cooling: review and prospects for enhanced surfaces / J.D. Benther et al // International Journal of Heat and Mass Transfer. – 2021. – Vol. 178. – Article 121587. https://doi.org/10.1016/j.ijheatmasstransfer.2021.121587.

37. The simultaneous analysis of droplets’ impacts and heat transfer during spray cooling / V. Serdyukov et al // Water. – 2021. – Vol. 13, № 19. – Article 2730. https://doi.org/10.3390/w13192730.

38. Gao X. Effects of nozzle positioning on single-phase spray cooling / X. Gao, R. Li // International Journal of Heat and Mass Transfer. – 2017. – Vol. 115. – P. 1247-1257. https://doi.org/10.1016/j.ijheatmasstransfer.2017.08.095.

39. Experimental investigation of spray cooling on smooth and micro-structured surfaces / Z. Zhang et al // International Journal of Heat and Mass Transfer. – 2014. – Vol. 78. – P. 879-887. https://www.sciencedirect.com/science/article/abs/pii/S0017931014003159.

40. Characterization of spray atomization and heat transfer performance of pressure swirl nozzles / J.L. Xie et al // Experimental Thermal and Fluid Science. – 2013. – Vol. 46. – P. 18-26. https://www.sciencedirect.com/science/article/abs/pii/S1290072912003456.

41. Vitkovic P. Water distribution characteristics of spray nozzles in a cooling tower / P. Vitkovic // EPJ Web of Conferences. – 2015. – Vol. 92. – Article 02109. https://doi.org/10.1051/epjconf/20159202109.

42. Review on cooling tower nozzle types / K.G. Somasundar et al // Materials Today: Proceedings. – 2021. – Vol. 37. – P. 3016-3018. https://doi.org/10.1016/j.matpr.2020.08.723.

43. Viljoen D.J. Evaluation and performance prediction of cooling tower spray nozzles. Master’s thesis. Stellenbosch University, 2006. URL: https://scholar.sun.ac.za/.

44. Kloppers J.C. Cooling tower performance evaluation: Merkel, Poppe, and e-NTU methods of analysis / J.C. Kloppers, D.G. Kröger // Journal of Engineering for Gas Turbines and Power. – 2005. – Vol. 127, № 1. – P. 1-7. https://doi.org/10.1115/1.1787504.

45. Qureshi B.A. A complete model of wet cooling towers with fouling in fills / B.A. Qureshi, S.M. Zubair // Applied Thermal Engineering. – 2006. – Vol. 26, № 16. – P. 1982-1989. https://doi.org/10.1016/j.applthermaleng.2006.01.010.

46. Schmidt D.P. The internal flow of diesel fuel injector nozzles: a review / D.P. Schmidt, M.L. Corradini // International Journal of Engine Research. – 2001. – Vol. 2, № 6. – P. 1-22. https://doi.org/10.1243/1468087011545316.

47. Fu Q. Numerical simulation of the internal flow of swirl atomizer under ambient pressure / Q. Fu // Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. – 2016. – Vol. 230, № 10. – P. 1760-1770. https://doi.org/10.1177/0954406215598803.

48. 2D and 3D numerical modelling of internal flow of pressure-swirl atomizer / M. Malý et al // EPJ Web of Conferences. – 2019. – Vol. 213. – Article 02055. https://doi.org/10.1051/epjconf/201921302055.

49. Searching for a numerical model for prediction of pressure-swirl atomizer performance / M. Malý et al // Applied Sciences. – 2022. – Vol. 12, № 13. – Article 6357. https://doi.org/10.3390/app12136357.

50. Comprehensive theoretical formulation and numerical simulation of pressure-swirl atomizers with helical channels / J. Ronceros et al // Energies. – 2024. – Vol. 17, № 21. – Article 5414. https://doi.org/10.3390/en17215414.


Рецензия

Для цитирования:


Ахметов А.А., Ермоленко М.В., Степанова О.А. ГИДРОДИНАМИЧЕСКИЕ И ТЕПЛОФИЗИЧЕСКИЕ АСПЕКТЫ ОПТИМИЗАЦИИ ОРОСИТЕЛЬНЫХ УСТРОЙСТВ В ТЕХНИЧЕСКИХ СИСТЕМАХ РАСПЫЛЕНИЯ: ОБЗОР. Вестник Университета Шакарима. Серия технические науки. 2026;(3(23)):643-663. https://doi.org/10.53360/2788-7995-2026-3(23)-65

For citation:


Akhmetov A.A., Yermolenko M.V., Stepanova O.A. HYDRODYNAMIC AND THERMOPHYSICAL ASPECTS OF SPRAYING DEVICE OPTIMIZATION IN TECHNICAL SPRAY SYSTEMS: A REVIEW. Bulletin of Shakarim University. Technical Sciences. 2026;(3(23)):643-663. (In Russ.) https://doi.org/10.53360/2788-7995-2026-3(23)-65

Просмотров: 13

JATS XML


Creative Commons License
Контент доступен под лицензией Creative Commons Attribution 4.0 License.


ISSN 2788-7995 (Print)
ISSN 3006-0524 (Online)
X