ТЕХНИКАЛЫҚ БҮРКУ ЖҮЙЕЛЕРІНДЕГІ СУАРУ ҚҰРЫЛҒЫЛАРЫН ОҢТАЙЛАНДЫРУДЫҢ ГИДРОДИНАМИКАЛЫҚ ЖӘНЕ ЖЫЛУФИЗИКАЛЫҚ АСПЕКТІЛЕРІ – ШОЛУ
https://doi.org/10.53360/2788-7995-2026-3(23)-65
Аңдатпа
Мақалада техникалық жүйелердегі суару және бүрку құрылғыларының жұмыс істеуінің гидродинамикалық және жылуфизикалық аспектілеріне арналған заманауи зерттеулерге шолу ұсынылған. Жұмыстың мақсаты суару құрылғыларының конструкциялық, гидродинамикалық және жылуфизикалық параметрлерінің бүрку сипаттамалары мен жылу- және массаалмасу тиімділігіне әсері туралы заманауи ғылыми көзқарастарды жүйелеу болып табылады. Бүркілген ағынның қалыптасуын анықтайтын негізгі факторлар, соның ішінде жұмыс қысымы, сұйықтық шығыны, саптама геометриясы, бүріккіш түрі, тамшылардың өлшемі мен жылдамдығы, бүрку алауының ашылу бұрышы, сұйықтықтың таралу біркелкілігі және жұмыс ортасының қасиеттері қарастырылған. Суару құрылғыларының тиімділігі тек шығын мен қысыммен ғана емес, сонымен қатар тамшылы ағын құрылымымен және оның газдық ортамен, толтырмамен немесе жылуалмасу бетімен өзара әрекеттесу жағдайларымен анықталатыны көрсетілген. Тамшылы спектр, суару тығыздығы, саптаманың орналасуы, беттің күйі және жылуалмасу режимі шешуші рөл атқаратын бүрку арқылы салқындату мәселелеріне ерекше назар аударылған. Градирнялар мен буландырғыш жүйелер үшін жылу- және массаалмасу тиімділігін анықтайтын негізгі факторлардың бірі ретінде судың біркелкі таралуының маңызы көрсетілген. Сонымен қатар саптамалардағы ішкі ағынды және бүрку алауының қалыптасуын зерттеуге арналған CFD-модельдеу мүмкіндіктері қарастырылған. Суару құрылғыларын жобалау және оңтайландыру кезінде гидродинамикалық, жылуфизикалық және пайдалану параметрлерін кешенді түрде ескеру қажеттілігі туралы қорытынды жасалған.
Авторлар туралы
А. А. АхметовҚазақстан
Алихан Алибекович Ахметов – «Техникалық физика және жылуэнергетика» кафедрасының 8D05302 – «Техникалық физика» білім беру бағдарламасының докторанты
071412, Қазақстан Республикасы, Семей қаласы, Глинка көшесі, 20А
М. В. Ермоленко
Қазақстан
Михаил Вячеславович Ермоленко – техника ғылымдарының кандидаты, қауымдастырылған профессор, «Техникалық физика және жылу энергетикасы» кафедрасының аға оқытушысы
071412, Қазақстан Республикасы, Семей қаласы, Глинка көшесі, 20А
О. А. Степанова
Қазақстан
Ольга Александровна Степанова – техника ғылымдарының кандидаты, профессор, «Техникалық физика және жылу энергетикасы» кафедрасының меңгерушісі
071412, Қазақстан Республикасы, Семей қаласы, Глинка көшесі, 20А
Әдебиет тізімі
1. Lefebvre A.H. Atomization and Sprays / A.H. Lefebvre, V.G. McDonell. – 2nd ed. Boca Raton: CRC Press, 2017. https://www.routledge.com/Atomization-and-Sprays/LefebvreMcDonell/p/book/9781498736251.
2. Handbook of Atomization and Sprays: Theory and Applications / N. Ashgriz et al. – New York: Springer, 2011. https://doi.org/10.1007/978-1-4419-7264-4.
3. Nasr G.G. Industrial Sprays and Atomization: Design, Analysis and Applications / G.G. Nasr, A.J. Yule, L. Bendig. London: Springer, 2002. https://doi.org/10.1007/978-1-4471-3816-7.
4. Bayvel L. Liquid Atomization / L. Bayvel, Z. Orzechowski/ Washington: Taylor & Francis, 1993. https://www.routledge.com/Liquid-Atomization/Bayvel/p/book/9780891169598.
5. Sirignano W.A. Fluid Dynamics and Transport of Droplets and Sprays / W.A. Sirignano. 2nd ed. Cambridge: Cambridge University Press, 2010. https://www.cambridge.org/.
6. Multiphase Flows with Droplets and Particles / C.T. Crowe et al. 2nd ed. Boca Raton: CRC Press, 2011. https://www.routledge.com/Multiphase-Flows-with-Droplets-and-Particles/CroweSchwarzkopf-Sommerfeld-Tsuji/p/book/9781439840504.
7. Yarin A.L. Drop impact dynamics: splashing, spreading, receding, bouncing / A.L. Yarin // Annual Review of Fluid Mechanics. – 2006. – Vol. 38. – P. 159-192. https://doi.org/10.1146/annurev.fluid.38.050304.092144.
8. Rein M. Phenomena of liquid drop impact on solid and liquid surfaces / M. Rein // Fluid Dynamics Research. – 1993. – Vol. 12, № 2. – P. 61-93. https://doi.org/10.1016/0169-5983(93)90106-K.
9. Experimental investigations of spray characteristics of a pressure-swirl atomizer / X. Fan et al // Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy. – 2020. – Vol. 234, № 5. https://doi.org/10.1177/0957650919875612.
10. Experimental investigation of flat fan nozzle V-cut depths and its impact on spray characteristics / W. Mughal et al // Scientific Reports. – 2025. – Vol. 15. – Article 22959. https://doi.org/10.1038/s41598-025-05319-z.
11. Mondal D. Droplet size and velocity distributions in a spray from a pressure swirl atomizer: application of maximum entropy formalism / D. Mondal, A. Datta, A. Sarkar // Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. – 2004. – Vol. 218, № 7. – P. 737-749. https://doi.org/10.1243/0954406041319563.
12. Droplet spectrum of standard flat fan and hollow cone spray nozzles / J.P.A.R. Cunha et al // Pesquisa Agropecuária Brasileira. – 2004. – Vol. 39, № 10. – P. 977-985. https://apct.sede.embrapa.br/pab/article/view/6865.
13. ISO 5682-1:2017. Equipment for crop protection – Spraying equipment – Part 1: Test methods for sprayer nozzles. Geneva: International Organization for Standardization, 2017. https://www.iso.org/standard/60053.html.
14. ISO 25358:2018. Crop protection equipment – Droplet-size spectra from atomizers – Measurement and classification. Geneva: International Organization for Standardization, 2018. https://www.iso.org/.
15. ANSI/ASABE S572.3. Spray Nozzle Classification by Droplet Spectra. St. Joseph, MI: American Society of Agricultural and Biological Engineers, 2020. URL: https://elibrary.asabe.org/azdez.asp?AID=51101.
16. Miller P.C.H. Evaluation of a spray nozzle patternator / P.C.H. Miller // Journal of Agricultural Engineering Research. – 1986. – № 1. – P. 43-52. https://doi.org/10.1016/0261-2194(86)90032-3.
17. Laser Doppler and Phase Doppler Measurement Techniques / H.-E. Albrecht et al. Berlin: Springer, 2003. https://doi.org/10.1007/978-3-662-05165-8.
18. Effect of nozzle type, size and pressure on spray droplet characteristics / D. Nuyttens et al // Biosystems Engineering. – 2007. – Vol. 97, № 3. – P. 333-345. https://doi.org/10.1016/j.biosystemseng.2007.03.001.
19. Reducing ground and airborne drift losses in young apple orchards with PWM-controlled spray systems / R. Salcedo et al // Computers and Electronics in Agriculture. – 2021. – Vol. 184. – Article 106389. https://doi.org/10.1016/j.compag.2021.106389.
20. Characterization of activation pressure, flow rate and spray angle for PWM-controlled hollowcone nozzles / R. Salcedo et al // Biosystems Engineering. – 2022. – Vol. 218. – P. 139-152. https://doi.org/10.1016/j.biosystemseng.2022.04.002.
21. Effect of angled spray nozzle designs on spray distribution and droplet spectrum / M.M. Negrisoli et al // Revista Ciência Agronômica. – 2021. – Vol. 52, № 3. https://www.scielo.br/j/rca/a/3YNNjbRVPPQmDk8dPyHTD3f/.
22. Czaczyk Z. Spray classification for selected flat fan nozzles / Z. Czaczyk // Journal of Plant Protection Research. – 2012. – Vol. 52, № 1. https://www.plantprotection.pl/Spray-classification-forselected-flat-fan-nozzles,91811,0,2.html.
23. The international (BCPC) spray classification system including a drift potential factor / E.S.E. Southcombe et al // Proceedings of the Brighton Crop Protection Conference – Weeds. – 1997. – P. 371-380.
24. Spillman J.J. Spray impaction, retention and adhesion: an introduction to basic characteristics / J.J. Spillman // Pesticide Science. – 1984. – Vol. 15, № 2. – P. 97-106. https://doi.org/10.1002/ps.2780150202.
25. Hewitt A.J. Spray drift: impact of requirements to protect the environment / A.J. Hewitt // Crop Protection. – 2000. – Vol. 19, № 8-10. – P. 623-627. https://doi.org/10.1016/S0261-2194(00)00082-X.
26. Gaillard A. What determines the drop size in sprays of polymer solutions? / A. Gaillard, R. Sijs, D. Bonn // arXiv. 2021. https://arxiv.org/abs/2108.11163.
27. Kim J. Spray cooling heat transfer: the state of the art / J. Kim // International Journal of Heat and Fluid Flow. – 2007. – Vol. 28, № 4. – P. 753-767. https://doi.org/10.1016/j.ijheatfluidflow.2006.09.003.
28. Spray cooling and flash evaporation cooling: the current development and application / W.-L. Cheng et al // Renewable and Sustainable Energy Reviews. – 2016. – Vol. 55. – P. 614-628. https://doi.org/10.1016/j.rser.2015.11.014.
29. Liang G. Review of spray cooling – Part 1: Single-phase and nucleate boiling regimes, and critical heat flux / G. Liang, I. Mudawar // International Journal of Heat and Mass Transfer. – 2017. – Vol. 115. – P. 1174-1205. https://doi.org/10.1016/j.ijheatmasstransfer.2017.06.029.
30. Liang G. Review of spray cooling - Part 2: High temperature boiling regimes and quenching applications / G. Liang, I. Mudawar // International Journal of Heat and Mass Transfer. – 2017. – Vol. 115. – P. 1206-1222. https://doi.org/10.1016/j.ijheatmasstransfer.2017.06.030.
31. Horacek B. Single nozzle spray cooling heat transfer mechanisms / B. Horacek, K.T. Kiger, J. Kim // International Journal of Heat and Mass Transfer. – 2005. – Vol. 48, № 8. – P. 1425-1438. https://doi.org/10.1016/j.ijheatmasstransfer.2004.10.026.
32. Rybicki J.R. Single-phase and two-phase cooling characteristics of upward-facing and downward-facing sprays / J.R. Rybicki, I. Mudawar // International Journal of Heat and Mass Transfer. – 2006. – Vol. 49, № 1-2. P. 5-16. https://engineering.purdue.edu/mudawar/files/articlesall/2006/2006-01.pdf.
33. Estes K.A. Correlation of Sauter mean diameter and critical heat flux for spray cooling of small surfaces / K.A. Estes, I. Mudawar // International Journal of Heat and Mass Transfer. – 1995. – Vol. 38, № 16. – P. 2985-2996. https://doi.org/10.1016/0017-9310(95)00047-C.
34. Mudawar I. Assessment of high-heat-flux thermal management schemes / I. Mudawar // IEEE Transactions on Components and Packaging Technologies. – 2001. – Vol. 24, № 2. – P. 122-141. https://doi.org/10.1109/6144.926375.
35. Spray cooling as a high-efficient thermal management solution: a review / J. Yin et al // Energies. – 2022. – Vol. 15, № 22. – Article 8547. https://doi.org/10.3390/en15228547.
36. Heat transfer during multiple droplet impingement and spray cooling: review and prospects for enhanced surfaces / J.D. Benther et al // International Journal of Heat and Mass Transfer. – 2021. – Vol. 178. – Article 121587. https://doi.org/10.1016/j.ijheatmasstransfer.2021.121587.
37. The simultaneous analysis of droplets’ impacts and heat transfer during spray cooling / V. Serdyukov et al // Water. – 2021. – Vol. 13, № 19. – Article 2730. https://doi.org/10.3390/w13192730.
38. Gao X. Effects of nozzle positioning on single-phase spray cooling / X. Gao, R. Li // International Journal of Heat and Mass Transfer. – 2017. – Vol. 115. – P. 1247-1257. https://doi.org/10.1016/j.ijheatmasstransfer.2017.08.095.
39. Experimental investigation of spray cooling on smooth and micro-structured surfaces / Z. Zhang et al // International Journal of Heat and Mass Transfer. – 2014. – Vol. 78. – P. 879-887. https://www.sciencedirect.com/science/article/abs/pii/S0017931014003159.
40. Characterization of spray atomization and heat transfer performance of pressure swirl nozzles / J.L. Xie et al // Experimental Thermal and Fluid Science. – 2013. – Vol. 46. – P. 18-26. https://www.sciencedirect.com/science/article/abs/pii/S1290072912003456.
41. Vitkovic P. Water distribution characteristics of spray nozzles in a cooling tower / P. Vitkovic // EPJ Web of Conferences. – 2015. – Vol. 92. – Article 02109. https://doi.org/10.1051/epjconf/20159202109.
42. Review on cooling tower nozzle types / K.G. Somasundar et al // Materials Today: Proceedings. – 2021. – Vol. 37. – P. 3016-3018. https://doi.org/10.1016/j.matpr.2020.08.723.
43. Viljoen D.J. Evaluation and performance prediction of cooling tower spray nozzles. Master’s thesis. Stellenbosch University, 2006. URL: https://scholar.sun.ac.za/.
44. Kloppers J.C. Cooling tower performance evaluation: Merkel, Poppe, and e-NTU methods of analysis / J.C. Kloppers, D.G. Kröger // Journal of Engineering for Gas Turbines and Power. – 2005. – Vol. 127, № 1. – P. 1-7. https://doi.org/10.1115/1.1787504.
45. Qureshi B.A. A complete model of wet cooling towers with fouling in fills / B.A. Qureshi, S.M. Zubair // Applied Thermal Engineering. – 2006. – Vol. 26, № 16. – P. 1982-1989. https://doi.org/10.1016/j.applthermaleng.2006.01.010.
46. Schmidt D.P. The internal flow of diesel fuel injector nozzles: a review / D.P. Schmidt, M.L. Corradini // International Journal of Engine Research. – 2001. – Vol. 2, № 6. – P. 1-22. https://doi.org/10.1243/1468087011545316.
47. Fu Q. Numerical simulation of the internal flow of swirl atomizer under ambient pressure / Q. Fu // Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. – 2016. – Vol. 230, № 10. – P. 1760-1770. https://doi.org/10.1177/0954406215598803.
48. 2D and 3D numerical modelling of internal flow of pressure-swirl atomizer / M. Malý et al // EPJ Web of Conferences. – 2019. – Vol. 213. – Article 02055. https://doi.org/10.1051/epjconf/201921302055.
49. Searching for a numerical model for prediction of pressure-swirl atomizer performance / M. Malý et al // Applied Sciences. – 2022. – Vol. 12, № 13. – Article 6357. https://doi.org/10.3390/app12136357.
50. Comprehensive theoretical formulation and numerical simulation of pressure-swirl atomizers with helical channels / J. Ronceros et al // Energies. – 2024. – Vol. 17, № 21. – Article 5414. https://doi.org/10.3390/en17215414.
Рецензия
Дәйектеу үшін:
Ахметов А.А., Ермоленко М.В., Степанова О.А. ТЕХНИКАЛЫҚ БҮРКУ ЖҮЙЕЛЕРІНДЕГІ СУАРУ ҚҰРЫЛҒЫЛАРЫН ОҢТАЙЛАНДЫРУДЫҢ ГИДРОДИНАМИКАЛЫҚ ЖӘНЕ ЖЫЛУФИЗИКАЛЫҚ АСПЕКТІЛЕРІ – ШОЛУ. Шәкәрім Университетінің Хабаршысы. Техникалық ғылымдар сериясы. 2026;(3(23)):643-663. https://doi.org/10.53360/2788-7995-2026-3(23)-65
For citation:
Akhmetov A.A., Yermolenko M.V., Stepanova O.A. HYDRODYNAMIC AND THERMOPHYSICAL ASPECTS OF SPRAYING DEVICE OPTIMIZATION IN TECHNICAL SPRAY SYSTEMS: A REVIEW. Bulletin of Shakarim University. Technical Sciences. 2026;(3(23)):643-663. (In Russ.) https://doi.org/10.53360/2788-7995-2026-3(23)-65
JATS XML















